1. Afraid of "dirty"
If the parts such as fuel filter, oil filter, air filter, hydraulic oil filter and various filters are too dirty, the filtering effect will become worse, and too many impurities will enter the oil circuit cylinder, aggravating the wear of parts and increasing the possibility of failure; If it is blocked seriously, the vehicle will not work normally Dirty radiator of water tank, radiator of cylinder block and cylinder head of air-cooled engine, radiator of cooler and other parts will lead to poor heat dissipation and excessive temperature Therefore, such "dirty" parts must be cleaned and maintained in time
2. Fear of "heat"
دمای پیستون موتور خیلی زیاد است که به راحتی باعث گرم شدن و ذوب شدن و نگه داشتن سیلندر می شود. مهر و موم های لاستیکی، نوارهای مثلثی، لاستیک ها و غیره بیش از حد گرم می شوند، که به راحتی زود پیر می شوند، عملکرد را کاهش می دهند و عمر مفید را کوتاه می کنند. سیم پیچ استارت، ژنراتور، رگولاتور و سایر تجهیزات الکتریکی بیش از حد گرم می شود، که به راحتی سوزانده می شود و از بین می رود. یاتاقان خودرو باید در دمای مناسب نگهداری شود. اگر بیش از حد گرم شود، روغن روان کننده به سرعت خراب می شود که در نهایت منجر به سوختن بلبرینگ و آسیب دیدن خودرو می شود.
3. Afraid of "string"
Various coupling parts in the fuel system of diesel engine, the driving and driven gears in the main reducer of the drive axle, the hydraulic control valve block and valve stem, the valve core and valve sleeve in the full hydraulic steering gear, etc. These matching coupling parts are specially processed and ground in pairs during manufacturing. The matching is very precise. They are always used in pairs within the service life and must not be interchanged Some mutually matched parts, such as piston and cylinder liner, bearing bush and journal, valve and valve seat, connecting rod big end pad cover and rod body, have a relatively good fit after running in for a period of time. During maintenance, pay attention to assembly in pairs and do not "visit" each other
4. Fear "anti"
واشر سیلندر موتور را نمی توان در حین نصب برعکس نصب کرد، در غیر این صورت باعث فرسایش زودرس و آسیب به واشر سیلندر می شود. برخی از رینگ های پیستون با اشکال خاص نباید به صورت معکوس نصب شوند و باید مطابق با الزامات مدل های مختلف مونتاژ شوند. همچنین الزامات جهتی برای نصب پره های فن موتور وجود دارد. فن به طور کلی به دو دسته اگزوز و مکش تقسیم می شود که نمی توان آنها را معکوس کرد، در غیر این صورت منجر به اتلاف حرارت ضعیف و دمای بیش از حد موتور می شود. برای لاستیکهایی با الگوی جهتدار، مانند لاستیکهای الگوی شاه ماهی، علامت زمین پس از نصب باید نوک شاه ماهی را به سمت عقب نشان دهد تا از حداکثر نیروی محرکه اطمینان حاصل شود. به میل خود
5. Fear of "lack"
When repairing the vehicle, some small parts may be omitted due to negligence, and some people even think it doesn't matter whether they are installed or not, which is very dangerous and harmful Engine valve keys shall be installed in pairs. If they are missing or missing, the valve will lose control and damage the piston and other parts; The cotter pin, locking screw, safety plate or spring pad and other locking devices installed on the engine connecting rod bolt, flywheel bolt and transmission shaft bolt may lead to serious faults in use once they are omitted; Once the oil nozzle used to lubricate the gear in the engine timing gear chamber is missing, it will lead to serious oil leakage and low engine oil pressure; The loss of water tank cover, oil port cover and oil tank cover will invade sand and dust and aggravate the wear of all parts
6. Afraid of "oil"
The paper filter element of engine dry air filter has strong moisture absorption. If it is stained with oil, it is easy to suck the mixture with high concentration into the cylinder, resulting in insufficient air, increased fuel consumption and reduced engine power. The diesel engine may also cause "flying car"; If the triangular tape is stained with oil, it will accelerate its corrosion and aging, and slip easily, resulting in the reduction of transmission efficiency; If the brake shoe, friction plate and brake belt of dry clutch are stained with oil, it is easy to slip and work poorly, thus threatening driving safety; Greasy dirt on the starting motor and generator carbon brush will lead to insufficient starting motor power and low generator voltage due to poor contact Tire rubber is very sensitive to oil corrosion. Contact with oil will soften or peel the rubber. Short time contact will lead to abnormal damage or even serious damage to the tire
7. Afraid of "washing"
Some novice drivers or repairmen may think that all parts need cleaning. In fact, this understanding is one-sided For the paper air filter element of the engine, when removing the dust on it, you can't clean it with any oil. Just tap it gently with your hand or blow the high-pressure air from the inside to the outside of the filter element; Leather parts should not be cleaned with oil, but only with a clean rag
8. Fear of "pressure"
اگر پوشش لاستیک به مدت طولانی تحت فشار ذخیره شود و به موقع بر نگردد، به دلیل اکستروژن تغییر شکل داده و عمر مفید آن را تحت تأثیر قرار می دهد. اگر عنصر فیلتر کاغذی فیلتر هوا و فیلتر سوخت فشرده شود، تغییر شکل زیادی ایجاد می کند و نمی تواند به طور قابل اعتماد نقش فیلتر را بازی کند. مهر و موم روغن لاستیکی، نوار مثلثی و لوله روغن نباید اکسترود شوند، در غیر این صورت تغییر شکل داده و استفاده عادی را تحت تأثیر قرار می دهند.
9. Fear of "near fire"
محصولات لاستیکی مانند لاستیک، نوار مثلثی، حلقه توقف آب سیلندر و مهر و موم روغن لاستیکی، اگر نزدیک به منبع آتش باشد، به راحتی پیر می شوند، خراب می شوند یا آسیب می بینند. از سوی دیگر، آنها همچنین ممکن است باعث حوادث آتش سوزی شوند، به ویژه، برخی از خودروهای دیزلی در سرمای شدید زمستان به سختی راه اندازی می شوند. برخی از رانندگان اغلب از دمنده برای گرم کردن آنها استفاده می کنند. ما باید از سوختن خطوط، مدارهای روغن و غیره جلوگیری کنیم
10. Afraid of "Repetition"
Some parts should have been used once, but some drivers or repairmen reuse them for saving or because they don't understand the "taboo", which is very likely to lead to accidents Generally speaking, the engine connecting rod bolts, nuts, fixing bolts of imported diesel engine fuel injector, cylinder liner water blocking ring, sealing copper gasket, various oil seals and sealing rings of hydraulic system, as well as pin pieces and split pins at important parts must be replaced with new ones after disassembly; For the engine cylinder gasket, although no damage is found during maintenance, it is best to replace it with a new one, because the old one has poor elasticity, poor sealing and easy ablation damage. It needs to be replaced after a short time of use, which is time-consuming and laborious. Therefore, if there is a new one, it is better to replace it as much as possible